The first true British "hyper-dreadnoughts"

Comparison G3/N3

The term "super-dreadnought" was already coined when the Orion class was unveiled in 1909, armed with 13 in guns instead of 12-inch barrels. In 1913 when the first of the Queen Elisabeth class was launched, the term received a new meaning, as the new class not only carried 15 inch (381 mm) guns, but they were also way faster, moving at 24 knots instead of 21, earning the title of "fast battleship". The Revenge class was a "battleship on a budget". Smaller, slower, but armed the same and with the same protection, the class was not a popular one. The wartime experience and battle of Jutland redefined many pre-requisites for the class following the R's and the design of the Admiral class Battlecruiser showered the hopes of some who pushed for a "universal capital ship": one that was reasonably fast (more than the previous Revenge) and heavily armed.

In 1916, the US Congress had been persuaded by the naval department to build a navy "second to none", with a large number of battleships and battlecruisers. The same year, the Japanese also started a large programme called the 8-8 fleet while the British were converting two improved Revenge-class hulls as Renown-class battlecruisers. For the UK, the only new capital ships during wartime laid down were the Admiral-class battlecruisers. The Admiral class design was entirely revised after the Battle of Jutland in May 1916 and soon three of the ships of the class were cancelled, leaving Hood to be completed much later.

The US battleship plan fell back to building smaller ships, such as destroyers and ten light cruisers, but still intended to resume the construction of the Constitution class battlecruisers and South Dakota class battleships. Estimates by the Admiralty for the early 1920s meant the Royal Navy would numerically fall behind the US in terms of modern capital ships. Indeed in the US in 1920-21, four new BS were completed, five more were in construction, and seven more were planned to be laid down in 1920–21. The South Dakota class with their twelve 16-inch guns also outclassed any British capital ship and the Japanese had even more grandiose plans: One battleship has been completed since the end of the war, and three more were under construction. The Admiralty initially planned to build three battleships for one battlecruiser for the year 1921–22 but this was changed to four G3-class battlecruisers and four battleships the next year to keep their naval supremacy.

The design lineage, U, L, and N (1920)

The U series were two extra orders for Canada of the Queen Elizabeth class ships, instead of "Improved Agincourts". At the time, the Government tried to convince Canada to finance them. The designs involved were possibly to be copy-paste designs but records are very sketchy. Their nominal speed was 25kts, like QE but with a large single funnel. However, U4 was a game-changer, as it had all four turrets on the same level to solve the problem that early fire control systems had directing superfiring turrets. U5 had the forward turrets en echelon. Their main belt was sacrificed down to 12in exchange for better deck armour. This study was suspended in 1915 as the "repeats" were converted as the Renown class battlecruisers instead at Fisher's request.

By June 1920 two designs derived from the "U-4" were prepared, 50,000 long tons (51,000 t), with eight to nine main guns in four twin or three triple gun turrets. They swapped to a bold new gun caliber: 18-inch (457 mm), under development in 1919. The problem with these large ships was that their size was too much for British dockyards of the time, and they also couldn't pass through the Suez Canal. An additional problem was that these turrets were not placed in superfiring positions, to lower the centre of gravity and avoid the extra weight of the superfiring barbettes. However, this made end-on fire far weaker than on previous classes which did have superfiring turrets. This new generation could withstand 18in or 15in gunfire and was supposed to be a "universal" ship (blending both battlecruiser and battleship roles).

These grand designs however were scaled down in October 1920, then split into separate battleship and battlecruiser designs: The two projects (battleship and battlecruiser) were numbered respectively from J upwards and J downwards. Battleship designs thus went from L through N, the associated letter after the number reflecting twin or triple turret variants.



The 'L2' and 'L3' had superfiring guns, plus a 15-inch (381 mm) sloped waterline belt along with an 8 in armoured deck and 9 inch slopes. Both had a top speed of 25 knots (46 km/h; 29 mph), with the great novelty of having a transom stern and straight bow with no ram. D'Encourt himself suggested that the long standard stern was just "kissing the water" and was not going to miss if cut off square. By March 1920 Naval Engineer Haslar tested models with transoms for the initial battlecruiser design with the configuration cutoff at 30ft, 15ft, 7ft, 6 ft, and right at the rudder, with resistance curves identical. Loss of efficiency was noted however around 15 kts. Superintendent S. Payne finalized the stern design, going for a broad transom for stability in damaged condition, still equivalent to a 20ft longer hull.

The 'L2' design was 52,100 long tons, 70,000shp, 25kts, 4x2 18in, 8x2 6in, 6x1 4.7in HA, 4x10 2pdr, two ASW TTs 24.5in, 15in thick main belt/25° over 470ft long, 18,850 tons of armor (37.1% of the displacement).'L3' was lighter at 51,000 long tons, with the same powerplant, 3x3 18in, and the same main belt but was 445ft long and carried 17,800 tons of armour (36.3%).



'M2' and 'M3' were submitted later in 1920 with the aft turret(s) moved amidships to shorten the length of the armoured citadel. This saved 1,540 long tons/1,740 long tons of armour. However, the ship also had a reduced powerplant and top speed at 23–23.5 knots using two larger propeller shafts instead of four. In the first design, fire arcs were restricted to 60° off the bow/75° forward of the stern. Despite this, blast effects were to be severe on the bridge.

'M2' design was 805 (wl) x 106 x 33ft, 48,750 tons, 56,000shp, 23kts, 4x2 18in, 8x2 6in, 5x1 4.7in HA, 4x10 2pdr, 2x 24.5in TTs, same 15in main belt/25° over. 440ft, deck 8-9in for 17,310 tons total. 'M3' design was 765 (wl) x same, 46,000 tons and same shp for 23.5kts, 3x3 18in and same. Same main belt mounted internally, 401ft, same deck armor, for 16,060 tons. This was an aft engine design, saving 1,500-1,800 tons of armour. The lengthened version of the M3 design was eventually chosen by the admiralty. which was a basis for development leading to the N3, approved in November 1921.

The idea of saving weight by concentrating artillery in the same place was further developed with the modified M3 and her forward artillery, behind the bridge and machinery spaces. The tower bridge structure behind the first two gun turrets was also a novelty. There was no longer a tripod, providing a more stable basis, vibration-free for the fire-control station, and improved accommodation and protection. However, the proximity of the main artillery was seen as a future problem.

Design in detail

The N3 battleships were much larger than the Revenge class at 820 feet (249.9 m), by 106 feet (32.3 m) in width and 33 feet (10.1 m) deeply loaded, displacing an estimated 48,500 long tons (49,300 t) and having a double bottom 7 feet (2.1 m) deep. They had triple turrets, a novel arrangement for the British Navy, at least for such heavy guns. War experience also had the British use a higher muzzle velocity gun combined with a lighter shell to optimize its ballistic performance.

The second big novelty was that these guns were 18 in (457 mm). Considered as the next logical step, these guns were already planned by Japan and the US in 1918. Secondary armament would have comprised eight twin 6 in (152 mm) guns in turrets, and single-mounted 4.7 in (120 mm) AA guns. In 1926-27 they would have been equipped with four 10-barrel 2-pdr (40 mm (1.6 in)) AA guns. However, they still carried two torpedo tubes, upgraded to the 24.5 in (622 mm) caliber.

The powerplant was to comprise two geared steam turbine sets separated in two engine rooms, with the funnel further aft as to provide a better arc of fire for the aft turret. Small-tube boilers were supposed to produce 56,000 shaft horsepower, translated into 23 knots.

Hull construction

One of the great novelties of the N3 was the placement of the third turret, so close to the main bridge and facing the aft superstructure. This made chase defense virtually impossible. This was probably the most radical approach in the design, explained mostly by armour concerns (see later). The other novelty was that like the HMS Hood and G3 designs, the prow was a straight clipper one, with fine hull lines and clean flanks. The general design was still elliptic, but the forward flare was limited and the stern was cut, or "transom".

The other point of interest was that the massive bridge, located with practically all the main firing direction systems, was off-center forward, at about the same position as in the previous Revenge class. The major difference from all previous designs is that it was a unified multi-level structure, unlike the tripod-based structures of the past. This was a radical step, which encountered some resistance from the admiralty, but was supported by the engineers, as the latter were able to persuade the former that a rigid structure with two massive reinforced tubes and intermediate pillars would support the structure, even without the need of a tripod mast.

Immediately, some criticized this choice, with some merit, about the way this tall structure was both a potential stability issue and could act as a "sail" in high winds with potentially adverse effects on the ship's handling. But these concerns were studied too. The trapezoidal section from above showed the structure was narrow and prismatic and rested on two major strength points. However, this design was chosen mostly to allow the aft turret 'X' to fire forward at some angle. We can only guess how the bridge would have supported such an 18-in blast so close to it, however. It was light enough, being unarmoured, to avoid stability issues. This debate resurfaced when the Nelson class was designed. In the end, none of these battleships ever fired main guns from their "C" turret facing backward and close to the bridge to ever cause a probem.

The curious profile, with this tall tower and all artillery at its feet, somewhat contradicted the whole aft section, still more than 1/3 of the total length, which seemed strangely out of place for traditional designs. It only comprised a superstructure, supporting the unique funnel (absent of the bridge) and an extremely aft tripod service mizzen mast. Between secondary and AA artillery and service boats, it was still a busy section.


what-if the N3 was authorized by the treaty and completed, then modernized in the late 1930s. (Tzoli)

Overall, the G3/N3 design was controversial, to say the least, and to a part of the admiralty accustomed to the familiar, seemingly logical pyramid-like silhouette of past battleships, designed the same way since the Orion class in 1911, there was a certain "cringe factor". Although another part of the admiralty, notably the younger generation, defended the design based on mathematical logic and war lessons, the older "top brass" was apparently relieved as the Washington Treaty went on and these ships were forced to be cancelled.

Now the treaty still made an exception for the two Nelsons, won by the "young guard." Even so, between officers and even sailors accustomed too long to certain aesthetics, the new battleships were dubbed mockingly "Nelsol and Rodnol", compared to oil tankers. At least, the whole main artillery was put forward, and the bridge placed at the back, in a more logical and "reassuring" way.

Armor scheme

Precised design and armor scheme by Maciej Chodnicki 2012 (imgurl)

Unlike any previous British dreadnought, the US solution of "all or nothing" was adopted as the main protection scheme for both the N3s and G3s: Medium-thickness armour was removed from all consideration as stated in reports. This was so that heavy shells would pass through the non-vital parts of the ship instead of tearing through a weak armour belt and exploding in the ship. This was adopted for the Nevada class, and the logic was implacable and well demonstrated during the war. This however came with a trick: The armoured citadel had to keep enough reserve buoyancy for the sake of stability, even if the rest of the ship was riddled and flooded. This was the same "safety raft" concept as in US vessels. Calculations compared the maximal flooding possible with the citadel's internal volume.

The whole scheme was similar to the G3, just thicker: The waterline belt reached 15 inches and was angled outward at 25°. Thus the slope artificially increased thickness for close-range (direct) fire but was less efficient against plunging shellfire. It ran for 463 feet (141.1 m), starting just 9 feet (2.7 m) forward 'A' turret, and stopped at the 6-inch aft magazine.

It was tapered down on 115 feet (35.1 m), aft, to 13.5 inches (343 mm) over the engine and boiler rooms. In total, this belt was 14 feet 3 inches (4.3 m) high: 4 feet 6 inches (1.4 m) of it were below the waterline as designed.

Its lower edge abreast of the magazines went on for 3 feet (0.9 m) with a 4 inches (102 mm) thick plating, made of high-tensile steel at 36°: This was to prevent a shell entering the magazines, bouncing on a wave at high speed. The Citadel was enclosed by two 14-inch (356 mm) transverse bulkheads, for and aft the same.

There was an 8-inch (203 mm) armour deck, as long as the waterline belt, sloped down and connected to the belt's upper edge. Forward it went over the torpedo compartment, enclosed by its own extra separate transverse bulkhead 9 inches (229 mm) thick. The steering gear was protected overhead by the same, enclosed by a 6-inch (152 mm) thick bulkhead.

The turrets were protected by various plating thicknesses and sloped at 18 inches (457 mm) on their face, the slope making it artificially way thicker, but again, only to direct fire. The sides were assumed to be 14 inches (356 mm) with the roofs being 8 inches. Their barbettes were 15 inches thick above the citadel, likely reduced or deleted entirely below it.

The conning tower had walls 15 inches thick and its communications tube below, running to the upper deck, was 8 inches. The fire-control director atop it, assuming a roof protection role, was protected by a 4-6 inch roof.

The internal anti-torpedo bulges-hence the "clean" hull- were designed to withstand a standard 750-pound (340 kg) torpedo warhead detonation. Their design was inspired by bulges fitted to the Revenge class, considered to be the most advanced of the type. There was an outer air space, the inner buoyancy space, followed by a 2 inch (51 mm) thick longitudinal bulkhead wall. It was located 16 feet (4.9 m) inboard, making quite a buffer. Postwar tests on a replica showed that when the buoyancy spaces were filled with seawater, they proved much more effective compared to the heavier, more complex sealed steel crushing tubes (as on HMS Hood).

• Waterline belt: 15 inches (381 mm), 25° inwards slope, 463 ft long
• Vitals belt aft: 13.5 inches (343 mm)
• Transverse bulkheads: 14-inch (356 mm)
• Main armour deck: 8-inch (203 mm)
• Fwd and aft extra bulkheads: 8 and 6 in
• Main Turrets: Face 18 in, sides 14 in, roof 8 in
• Main barbettes: 15 in (381 mm)
• Conning Tower: 15 walls
• Fire-control director 4-6 in (152 mm)
• Longitudinal ASW bulkhead 2 in (51 mm)

Powerplant

Probably the least innovative part of the design, although the whole housing section for it was relocated aft, making way for the "X" barbette and ammunition magazine at the ship's center, was the ship's powerplant. The ships would have been given two geared steam turbine sets, two propeller shafts that were connected to two engine rooms, both located forward of the boiler rooms in order to truncate the funnel in a way that it could be relocated much further aft, cleaning the arc of fire for the same "X" aft turret. Boilers were of the small-tube type, lighter and smaller, more compact, yet they still gave a rated total of 56,000 shaft horsepower (42,000 kW). The top speed was less than the Queen Elisabeth class, at just 23 knots.

This powerplant was more rational, compact, and simpler, and helped in that by the choice of small-tube boilers rated as designed for 56,000 shaft horsepower. 23 knots was less than the QE class but on par with the more recent Revenge class. The QEs indeed had four shafts and turbines, 24 water-tube boilers for 75,000 shp (56,000 kW), and 24 knots. It was a middle ground between the QE and slower Revenge in order to fit the battle fleet line. So despite the fact the N3 were about 15,000 tonnes heavier, they had less overall power than their predecessors.

Armament

Main: 3x3 18-in/45

Just after WWI, the admiralty started investigating new battleship and battlecruiser designs, in order to incorporate all wartime lessons, and have ships larger and more powerful than HMS Hood. Five different main gun sizes, 15"/50 (38.1 cm), 16"/45 (40.6 cm), 16.5"/45 (41.9 cm), 16.5"/50 (41.9 cm) and 18"/45 (45.7 cm) were studied right away. After a lot of calculations and detailed design work, nine 16"/45 (40.6 cm) guns were chosen for the G3 battlecruiser design, while their "battleship" equivalents, the N3 class, were to receive nine 18"/45 (45.7 cm) by late 1920.

British designers were aware of USN gun designs and at Scapa, could see in-detail German gun designs, leading to a new gun construction technique. Instead of a full-length wire-wound method, the existing 16"/45 (40.6 cm) were just slightly modified for Battlecruisers, which were urgent. But it was agreed to take more time for the Battleship guns.

Elswick, Vickers, and the Royal Gun Factory were all asked for proposals for a modern 18"/45 (45.7 cm) ordnance, based on three new construction methods to do comparative testings:
The Elswick design was a full-length wire-wound gun cast with a new taper winding process.
The Vickers design went for a partial-length wire-wound gun.
The RGF was the most innovative, proposing a "no wire" gun with longer tubes.
In total, more than 30 designs were submitted, keeping Ordnance Committee busy. They opted eventually for the Royal Gun Factory design but still wanted to experiment with the other two construction methods and orders were placed for a Vickers partially wired gun (No. 5) the Elswick being a "no wire" (No. 6), signed on 22 December 1920. The Royal Gun Factory from Woolwich had the full-length taper wound wire gun (No. 4) to make, signed on 20 January 1921. Krupp manufacturing techniques were also to be studied by the latter, with a precision shrinking process, but it went nowhere. Officially these were all "16-in/50 (40.6 cm)" guns.

However, on 30 January 1922, still many months before delivery and close to the signature of the Washington Naval Limitation Treaty, the whole program was cancelled. Authorized guns, as feared, went back to 16"/45 (40.6 cm) calibers. The turrets ordered for the "G3" battlecruisers were reused, after some trimming on the HMS Nelson and Rodney.

The 18"/45 (45.7 cm) Mark II nevertheless became the wet dream of the admiralty and were on paper the most powerful guns ever fitted on a British warship. There had been 18-in guns in the past, those planned for the Furious class battlecruisers, but they were only used for tests: The 18"/40 (45.7 cm) Mark I, a gun so heavy that a single turret was designed for them. After Furious was converted, they saw action on Monitors.

Still, given the problems already noted on the 16-in, it was unlikely these new guns would have been used for operations on the N3s. Besides, the British admiralty had no intention to go further, as found by Sir Robert Hadfield who proposed 20-21 in APC shells and was flatly denied. In fact, the admiralty and government both agreed to stop R&D well before the Washington Naval Limitations were signed. Since they were a paper project, the performance of these guns were difficult to assess. They would have been given a 55,000 in3 (901.3 dm3) chamber volume, with shells ranging in weight from 2,916 lbs. (1,323 kg) for the APC, and 3,000 lbs. (1,361 kg) for the HE in 1921. Their propellant charge was to weigh about 810 lbs. (367 kg). Muzzle velocity for the lighter APC version would have been 2,916 lbs. (1,323 kg) APC - About 2,650 fps (808 mps), with a barrel life below 100 rounds. Their maximum range at an elevation of 40 degrees was about 42,000 yards (38,405 m).

Maximum penetration, at zero obliquity was 36.82 inches (935.3 mm) of armor at 2,700 fps, (based on a USN Empirical Formula for Armor Penetration) so that on paper, they were the most powerful naval weapons in the world, even ahead of the later 460 mm guns of the Yamato.

Secondary:

The N3s had a less than impressive secondary armament of sixteen BL 6-inch Mk XXII guns. The novelty there was that based on past experiences, none was in casemates (henceforth another reason for a clean hull), and neither were they in triple turrets like for the Renown class or open batteries like for the Hood. They were all in superfiring twin turrets: According to the sketch, two pairs abreast the main bridge forward, two on the aft battery deck abreast the funnel, two at deck level in structure recesses, and two aft, close to the transom stern.

The concept was not new as such turret was experimented with success on HMS Enterprise

• Elevation –5° and +60°
at a Their elevation. Their rate of fire was five rounds per minute.
• 100-pound (45 kg) HE or AP shell
• Muzzle velocity of 2,945 ft/s (898 m/s).
• Max range 25,800 yd (23,600 m)/45°
• Rate of fire: Five rounds per minute

Tertiary:

This was a rather heavy armament for the time, with six single mounts, unprotected QF 4.7-inch Mk VIII guns, placed on the aft superstructure and stern. Here are the specs:

• Depression -5° elevation 90°
• 50 Ib (23 kg) high explosive shell
• Muzzle velocity of 2,457 ft/s (749 m/s)
• Rate of Fire 12 rpm
• Ceiling of 32,000 ft

In addition, the closer range defense was to be assumed by four 10-barreled mountings 2-pdr (40mm /1.6 in) "pom-pom" guns. They were located between the funnel (2) and stern (2). Each was provided with 1,300 rounds of ammunition and fired a (1.6 in) 0.91-pound (0.41 kg) HE shell at 1,920 ft/s (590 m/s) over 3,800 yards (3,500 m) at around 96–98 rpm. The ten-barrel mounts in the end proved impractical and eventually, the RN settled on quad (1936) or octuple ones (1930).

Torpedoes:

Lastly, as in previous designs, they were to carry submerged torpedo tubes, even as Jutland proved these were pretty much a waste of time. These were two submerged broadside torpedo tubes, located just forward of the 'A' shell room, on the platform deck. In storage, there were six 24.5-inch (622 mm) per tube in peacetime with the ship carrying 12 in peacetime and 16 in wartime. Mark I torpedoes: 743 pounds TNT (337 kg) oxygen-enriched air, 15,000 yards/35 kts and 20,000 yards/30 kts settings.

Fire control:

The main guns were controlled from the two director-control towers (DCT), located on the main bridge, one on the 1st level, CT roof, right above the "B" turret, and the other on the roof of the bridge. The first one was protected by an armoured barbette above the conning tower's armoured hood.

Each main gun turret was also provided with a 41-foot (12.5 m) coincidence rangefinder, in an armoured roof housing.

Secondary guns were to be controlled by two DCTs on each side of the bridge (three positions). Anti-aircraft gunnery control rested in the high-angle FCS on top of the mizzenmast's tripod on the aft of the ship. The 2-pdr pom-pom AA mounts had their director and could be fed by the info from height-finders aft.

Two 15-foot (4.6 m) torpedo rangefinders were placed on both funnel's platforms, along with the search projectors.

There were three masts, but only two are clearly shown on the N3 draft: A main mast aft of the bridge, on top of the aft strength tube, a tripod forward of the funnel, and a larger mizzen mast tripod aft of it, to handle service boats. The presence of an intermediary tripod was probably to handle extra service boats, but it could have been handy if these ships were fitted with spotter seaplanes.

Fate

They were never ordered: With the Washington Naval Treaty under negotiation at the time, The admiralty did not want to start battleships that would have been cancelled soon after, as they beleived (correctly) that it was probably going to be signed. However, many of their design aspects were incorporated into the two Nelson-class battleships, often compared as scaled-down, cheaper N3s with lighter guns. Their design received the designation 'O3', next in the design sequence. They complied with the treaty's 16-inch limitation and were well noted and studied by navies at that time.

Eventually, although they had been approved, the N3 class battleships (prospective name generally admitted, St. Andrews class, in fact, the four patron saints of the United Kingdom, with HMS St. George, HMS St. Patrick, and HMS St. David had prospectively been selected). They would have been logically completed in 1922-23, and probably modernized, at least partially as were some QE and Revenge classes; Even the Nelson class (which would have never been born) were modernized in the late 1930s.

With such main guns though, if the Washington treaty was never signed, the Royal Navy would have faced even faster US and Japanese vessels, for the latter probably armed with the projected 51 cm guns for the precursors of the Yamatos. The two Rodneys versus these four "saints" were just budget, treaty-capped versions.


Design N3 HMS St Andrews by the author

⚙ N3 class specifications
Dimensions	249,9 x 32,3 x 10,1 m (820 x 106 x 33 ft)
Displacement	48,500-49,300t normal - 55,000t est. FL
Crew	1200 estimated
Propulsion	2 shaft GS Turbines, 20 Yarrow boilers, 56.000 shp
Speed	23 knots top speed
Range	Unknown
Armament	3x3 18-in, 8x2 6-in, 6x1 4.7 in, 4x10 2Pdr Pompom AA
Armor (max)	Belt 15, Deck 8, Barbettes 15, Turret 18, CT 15, Bulkheads 14 in

3D Impression

Note: This is a modification of the Nelson, not a proper rendition of the type.

Read More/Src

Navweaps pompom
Navweaps proposed 18 in guns
Navweaps 6"/50 (15.2 cm) BL Mark XXII
Navweaps 4.7"/40 (12 cm) QF Mark X
Navweaps 2-pdr [4 cm/39 (1.575")] Mark VIII
Navweaps British Torps Interwar
Wiki
Video: N3 class Drachinfels

---

Gardiner, Robert. Conway's All the World's Fighting Ships 1906–1921
Brown, David K. (1999). The Grand Fleet: Warship Design and Development 1906–1922.
Campbell, N. J. M. (1977). "Washington's Cherry Trees". Warship. London: Conway Maritime Press.
Friedman, Norman (1985). U.S. Battleships: An Illustrated Design History.
Raven, Alan & Roberts, John (1976). British Battleships of World War Two from 1911 to 1946.

---

Model kits

On scalemates: 700-N3, HMS St. Andrew N3 1921 - Imperial Hobby Productions (IHP) 1:700

Gallery

St Vincent renditions by World of Warships